Fortinet 548B Manual de usuario Pagina 684
- Pagina / 969
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
- 684 -
Broadcast Poll Interval - Specifies the number of seconds between broadcast poll requests
expressed as a power of two when configured in broadcast mode. Broadcasts received prior to the
expiry of this interval are discarded. Allowed range is (6 to 10). Default value is 6.
Multicast Poll Interval - Specifies the number of seconds between multicast poll requests
expressed as a power of two when configured in multicast mode. Multicasts received prior to the
expiry of this interval are discarded. Allowed range is (6 to 10). Default value is 6.
Unicast Poll Timeout - Specifies the number of seconds to wait for an SNTP response when
configured in unicast mode. Allowed range is (1 to 30). Default value is 5.
Unicast Poll Retry - Specifies the number of times to retry a request to an SNTP server after the
first time-out before attempting to use the next configured server when configured in unicast mode.
Allowed range is (0 to 10). Default value is 1.
Command Buttons
Submit - Sends the updated configuration to the switch. Configuration changes take effect
immediately.
11.2.13.2 Viewing SNTP Global Status Page
Non-Configurable Data
Version - Specifies the SNTP Version the client supports.
Supported Mode - Specifies the SNTP modes the client supports. Multiple modes may be
supported by a client.
Last Update Time - Specifies the local date and time (UTC) the SNTP client last updated the
system clock.
Last Attempt Time - Specifies the local date and time (UTC) of the last SNTP request or receipt of
an unsolicited message.
- FortiSwitch-548B 1
- Table of Contents 3
- - 4 4
- - 5 5
- 1. Introduction 6
- - 7 7
- 2. Product Overview 8
- 2.3 Front-Panel Components 10
- 2.4 LED Indicators 10
- 2.5 Rear Panel Description 10
- 2.6 Management Options 11
- 2.9 SNMP-Based Management 11
- 3.1 Package Contents 13
- 3.2 Switch Installation 14
- 5.1 Overview 24
- 5.2 How to log in 25
- 6.1 CLI Command Format 30
- 6.2 CLI Mode-based Topology 31
- 0.0.0.0 to 255.255.255.255 32
- YY:YY:YY:YY:YY:YY 32
- 7. Switching Commands 33
- 7.1.3 show process cpu 34
- 7.1.6 show sysinfo 36
- 7.1.7 show system 36
- 7.1.8 show tech-support 37
- 7.1.9 show hardware 37
- 7.1.10 show version 39
- 7.1.11 show loginsession 40
- 7.1.12 show command filter 41
- 7.2.1 Interface 41
- 7.2.1.6 negotiate 50
- 7.2.1.7 capabilities 51
- 7.2.1.11 description 54
- 7.2.1.12 mdi 54
- 7.2.2.1 show mac-addr-table 55
- 7.2.3 VLAN Management 61
- 7.2.3.1 show vlan 61
- 7.2.3.2 show vlan id 61
- 7.2.3.5 show protocol group 63
- 7.2.3.7 vlan database 65
- 7.2.3.8 vlan 65
- 7.2.3.9 vlan name 65
- 7.2.3.12 vlan makestatic 67
- 7.2.3.13 protocol group 67
- 7.2.3.18 switchport tagging 72
- 7.2.4 Double VLAN commands 76
- 7.2.5.1 show bridge-ext 78
- 7.2.5.5 bridge-ext gvrp 81
- 7.2.5.6 bridge-ext gmrp 81
- 7.2.5.7 switchport gvrp 81
- 7.2.5.8 switchport gmrp 82
- 7.2.5.9 garp timer 83
- 7.2.6 IGMP Snooping 87
- 7.2.6.1 ip igmp snooping 87
- 7.2.6.8 set igmp 90
- 7.2.6.9 set igmp fast-leave 91
- 7.2.7 IGMP Snooping Querier 96
- 7.2.8 MLD Snooping 101
- 7.2.8.6 ipv6 mld snooping 105
- 7.2.8.7 clear mld snooping 105
- 7.2.8.15 set mld 108
- 7.2.8.16 set mld fast-leave 109
- 7.2.9 MLD Snooping Querier 110
- 7.2.10 Port Channel 115
- 7.2.10.1 show port-channel 115
- 7.2.10.2 port-channel 117
- 7.2.10.4 staticcapability 118
- 7.2.10.7 port-channel name 120
- 7.2.10.9 adminmode 121
- 7.2.10.10 lacp 122
- 7.2.10.12 channel-group 125
- 7.2.11 Storm Control 126
- 7.2.11.1 show storm-control 126
- 7.2.12 L2 Priority 133
- 7.2.12.1 show queue cos-map 133
- 7.2.12.2 queue cos-map 134
- 7.2.13 Port Mirror 134
- 7.2.14 Link State 136
- 7.2.14.1 show link state 136
- 7.2.14.2 link state 137
- 7.2.14.3 link state group 137
- 7.2.15 Port Backup 138
- 7.2.15.1 show port backup 138
- 7.2.15.2 port-backup 138
- 7.2.15.3 port-backup group 139
- 7.2.16 FIP Snooping 139
- 7.2.16.1 show fip-snooping 139
- 7.2.16.6 fip-snooping 142
- 7.2.16.7 fip-snooping vlan 142
- 7.2.17.1 show queue ets 143
- 7.2.17.5 queue ets 144
- Disabled 148
- 0-16777215 > 150
- 7.3 Management Commands 152
- 7.3.1.2 show ip filter 153
- 7.3.1.3 mtu 154
- 7.3.1.4 interface vlan 154
- 7.3.1.5 ip address 155
- 7.3.1.6 ip default-gateway 155
- 7.3.1.7 ip address protocol 156
- 7.3.1.8 ip filter 156
- 7.3.2.1 show line console 157
- 7.3.2.2 line console 158
- 7.3.2.3 baudrate 158
- 7.3.2.4 exec-timeout 159
- 7.3.2.5 password-threshold 159
- 7.3.2.6 silent-time 159
- 7.3.2.7 terminal length 160
- 7.3.3.1 telnet 160
- 7.3.3.2 show line vty 161
- 7.3.3.3 line vty 162
- 7.3.3.4 exec-timeout 162
- 7.3.3.5 password-threshold 162
- 7.3.3.6 terminal length 163
- 7.3.3.7 maxsessions 163
- 7.3.3.8 server enable 164
- 7.3.3.9 sessions 164
- 7.3.3.10 telnet sessions 165
- 7.3.3.11 telnet maxsessions 165
- 7.3.3.13 show telnet 166
- 7.3.4.1 ssh 167
- 7.3.4.2 sshc sessions 167
- 7.3.4.3 sshc maxsessions 168
- 7.3.4.4 sshc exec-timeout 168
- 7.3.4.5 show sshc 168
- 7.3.5 SNMP Server Commands 169
- 7.3.5.1 show snmp 169
- 7.3.5.2 show trapflags 170
- 7.3.5.3 snmp-server sysname 171
- 7.3.5.5 snmp-server contact 172
- 7.3.6.6 snmptrap mode 181
- 7.3.7 HTTP commands 182
- 7.3.7.1 show ip http 182
- 7.3.7.2 ip javamode 182
- 7.3.7.3 ip http port 183
- 7.3.7.4 ip http server 183
- 7.3.7.5 ip http secure-port 184
- 7.3.8.1 show ip ssh 185
- 7.3.8.2 ip ssh 186
- 7.3.8.3 ip ssh protocol 186
- 7.3.8.5 ip ssh timeout 187
- 7.3.9.2 crypto key generate 188
- 7.3.10 DHCP Client Commands 189
- 7.3.10.1 ip dhcp restart 189
- 7.3.11.2 ipv6 dhcp restart 190
- 7.3.12 DHCP Relay Commands 191
- 7.3.13 sFlow Commands 192
- 7.3.13.1 show sflow agent 192
- 7.3.13.2 show sflow pollers 193
- 7.3.13.5 set sflow rate 195
- 7.3.14.1 show serviceport 198
- 7.3.14.3 serviceport ip 199
- 7.4 Spanning Tree Commands 202
- 7.4.2.1 spanning-tree 209
- 7.4.2.4 spanning-tree mode 211
- 7.4.2.10 spanning-tree mst 214
- 7.5.1 Show Commands 222
- 7.5.1.1 show logging 222
- 7.5.1.4 show logging hosts 224
- 7.5.2.1 logging buffered 224
- 7.5.2.2 logging console 225
- 7.5.2.3 logging monitor 226
- 7.5.2.4 terminal monitor 226
- 7.5.2.5 logging host 227
- 7.5.2.6 logging syslog 228
- 7.6.1 script apply 229
- 7.6.2 script delete 229
- 7.6.2.1 script list 230
- 7.6.3 script show 230
- 7.6.4 script validate 231
- 7.7.1 Show Commands 231
- 7.7.1.1 show users 231
- 7.7.2.1 username 233
- 7.8 Security Commands 237
- 7.8.1.2 show authentication 238
- 7.8.1.4 show dot1x 239
- 7.8.1.5 show dot1x detail 239
- 7.8.1.7 show dot1x summary 242
- 7.8.1.8 show dot1x users 242
- 7.8.1.9 show dot1x client 243
- 7.8.1.11 show radius 244
- 7.8.1.14 show tacacs 247
- 7.8.1.15 show port-security 248
- 7.8.2.3 username login 251
- 7.8.3.1 dot1x initialize 252
- 7.8.3.2 dot1x default-login 252
- 7.8.3.3 dot1x login 253
- 7.8.3.5 dot1x user 254
- 7.8.3.6 dot1x port-control 254
- 7.8.3.7 dot1x max-req 255
- 7.8.3.8 dot1x max-user 256
- 7.8.3.11 dot1x timeout 257
- 7.8.3.12 dot1x guest vlan 258
- 7.8.4.5 radius-server host 260
- 7.8.4.6 radius-sever key 261
- 7.8.5.1 tacacs host 264
- 7.8.5.2 tacacs key 264
- 7.8.5.3 tacacs timeout 266
- 7.8.6.1 port-security 267
- 7.9.1 Show Commands 269
- 7.9.1.1 show cdp 269
- 7.9.1.2 show cdp neighbors 270
- 7.9.1.4 show cdp traffic 271
- 7.9.2.1 cdp 271
- 7.9.2.2 cdp run 272
- 7.9.2.3 cdp timer 273
- 7.9.2.4 cdp holdtime 273
- 7.10.1 Show Commands 274
- 7.10.1.1 show sntp 274
- 7.10.2.2 sntp client mode 276
- 7.10.2.3 sntp client port 277
- 7.10.2.7 sntp server 278
- 7.11.1 Show Commands 280
- 7.11.1.1 show voice-vlan 280
- 7.11.1.2 show voice vlan 281
- 7.11.2.1 voice-vlan 281
- 7.11.2.2 voice-vlan vlan 282
- 7.11.2.3 voice-vlan mac 282
- 7.11.2.4 voice vlan 283
- 7.12.1 Show Commands 284
- 7.12.1.1 show lldp 284
- 7.12.1.8 show lldp med 289
- 7.12.2.1 lldp notification 294
- 7.12.2.3 lldp receive 295
- 7.12.2.4 lldp transmit 295
- 7.12.2.5 lldp transmit-mgmt 295
- 7.12.2.6 lldp transmit-tlv 296
- 7.12.2.7 lldp timers 296
- 7.12.2.8 lldp tx-delay 297
- 7.12.2.9 lldp med 298
- 7.12.2.12 lldp med all 299
- 7.13.1 Show Commands 301
- 7.13.1.1 show dos-control 301
- 7.13.2.1 dos-control sipdip 302
- 7.13.2.8 dos-control icmp 305
- 7.13.2.9 dos-control icmpv4 306
- 7.13.2.17 dos-control all 310
- 7.14.1 Show Commands 310
- 7.14.1.1 show vtp counters 310
- 7.14.1.2 show vtp password 311
- 7.14.1.3 show vtp status 311
- 7.14.1.4 show vtp trunkport 312
- 7.14.2.1 vtp 312
- 7.14.2.2 vtp domain 313
- 7.14.2.3 vtp mode 313
- 7.14.2.4 vtp version 314
- 7.14.2.5 vtp password 314
- 7.14.2.6 vtp pruning 315
- 7.14.2.7 vtp trunkport 315
- 7.15.1 Show Commands 316
- 7.16.1 Show Commands 318
- 7.16.2.1 macfilter 319
- 7.16.2.2 macfilter addsrc 319
- 7.17 System Utilities 321
- 7.17.1.5 clear config 322
- 7.17.1.6 clear pass 323
- 7.17.1.7 clear counters 323
- 7.17.1.8 clear dns 323
- 7.17.1.9 clear cdp 324
- 7.17.1.10 clear vlan 324
- 7.17.1.13 clear ip filter 325
- 7.17.1.16 clear domain-list 327
- 7.17.1.17 clear hosts 327
- 7.17.1.22 enable passwd 329
- 7.17.1.26 clear ipv6 dhcp 331
- 7.17.2 copy 331
- 7.17.3 delete 333
- 7.17.4 dir 334
- 7.17.5 whichboot 334
- 7.17.6 boot-system 335
- 7.17.7 ping 335
- 7.17.8 traceroute 337
- 7.17.8.1 traceroute 337
- 7.17.8.2 traceroute ipv6 338
- 7.17.9 logging cli-command 339
- 7.17.10 calendar set 339
- 7.17.11 reload 339
- Default Setting 340
- 7.17.12 configure 340
- 7.17.13 disconnect 340
- 7.17.14 hostname 341
- 7.17.15 quit 341
- 7.17.16 cablestatus 341
- 7.18 DHCP Snooping Commands 342
- 7.18.1 Show Commands 343
- 7.18.2.1 ip dhcp snooping 345
- 7.19.1 Show Commands 351
- 7.19.1.1 show ip verify 351
- 7.19.2.1 ip verify source 352
- 7.19.2.2 ip verify binding 353
- 7.20.1 Show Commands 354
- 7.20.2.7 arp access-list 358
- 7.21.1 General Commands 361
- 7.21.1.1 diffserv 361
- services are activated 362
- 7.21.2.2 no class-map 363
- 7.21.2.3 class-map rename 363
- 7.21.2.4 match any 364
- 7.21.2.5 match class-map 364
- 7.21.2.6 no match class-map 365
- 7.21.2.7 match cos 366
- 7.21.2.9 match dstip 367
- 7.21.2.10 match dstl4port 367
- 7.21.2.11 match ethertype 368
- 7.21.2.12 match ip dscp 368
- 7.21.2.14 match ip tos 369
- <tosmask> of a2 (hex) 370
- 7.21.2.15 match protocol 370
- 7.21.2.17 match srcip 371
- 7.21.2.18 match srcl4port 372
- 7.21.2.19 match vlan 372
- 7.21.2.20 match dstip6 373
- 7.21.2.21 match srcip6 373
- 7.21.2.22 match ip6flowlbl 373
- 7.21.3 Policy Commands 374
- 7.21.3.1 assign-queue 375
- 7.21.3.2 drop 375
- 7.21.3.3 mirror 375
- 7.21.3.4 redirect 376
- 7.21.3.5 conform-color 376
- 7.21.3.6 mark cos 377
- 7.21.3.7 class 377
- 7.21.3.8 no class 378
- 7.21.3.9 mark ip-dscp 378
- 7.21.3.11 police-simple 379
- 7.21.3.12 policy-map 380
- 7.21.3.13 policy-map rename 380
- 7.21.4 Service Commands 381
- 7.21.4.1 service-policy 381
- 7.21.4.2 no service-policy 382
- 7.21.5 Show Commands 382
- 7.21.5.1 show class-map 383
- 7.21.5.2 show diffserv 383
- service 384
- service brief 385
- 7.22 ACL Command 389
- 7.22.2.4 mac access-list 393
- 7.22.2.5 access-list 394
- 7.22.2.6 no access-list 395
- 7.22.2.7 ip access-group 395
- 7.22.2.8 ip access-list 396
- 7.23 IPv6 ACL Command 397
- 7.23.2.1 ipv6 access-list 398
- 7.24.1 Show Commands 401
- 7.24.1.1 show queue cos-map 401
- 7.24.1.3 show queue trust 402
- 7.24.2.1 queue cos-map 404
- 7.24.2.2 queue trust 404
- 7.25.1 Show Commands 408
- 7.25.1.1 show hosts 408
- 7.25.1.2 show dns 408
- 7.25.1.3 show dns cache 409
- 7.25.2.1 ip hosts 409
- 7.25.2.2 clear hosts 410
- 7.25.2.3 ip domain-name 410
- 7.25.2.4 ip domain-list 411
- 7.25.2.5 ip name-server 411
- 7.25.2.6 ip domain-lookup 412
- 7.25.2.8 clear dns 412
- 7.25.2.9 clear dns cache 413
- 7.25.2.10 clear dns counter 413
- 8. Routing Commands 414
- 8.1.1.2 show ip arp brief 415
- 8.1.1.3 show ip arp static 415
- 8.1.2.1 arp 416
- 8.1.2.2 ip proxy-arp 416
- 8.1.2.3 ip local-proxy-arp 417
- 8.1.2.4 arp cachesize 417
- 8.1.2.5 arp dynamicrenew 418
- 8.1.2.6 arp purge 418
- 8.1.2.7 arp resptime 418
- 8.1.2.8 arp retries 419
- 8.1.2.9 arp timeout 419
- 8.2 IP Routing Commands 420
- 8.2.1.4 show ip route 422
- 8.2.1.6 show ip route entry 424
- 8.2.1.8 show ip route ospf 425
- 8.2.1.9 show ip route rip 426
- 8.2.2.1 routing 428
- 8.2.2.2 ip routing 429
- 8.2.2.3 ip address 429
- 8.2.2.4 ip route 430
- 8.2.2.5 ip route default 430
- 8.2.2.7 ip mtu 431
- 8.2.2.8 encapsulation 432
- 8.3.1 Show Commands 432
- 8.3.1.1 show ip ospf 432
- 8.3.1.2 show ip ospf abr 434
- 8.3.1.3 show ip ospf area 435
- 8.3.1.4 show ip ospf asbr 437
- 8.3.1.11 show ip ospf range 444
- 8.3.2.1 router ospf 447
- 8.3.2.2 enable 447
- 8.3.2.3 network area 448
- 8.3.2.4 ip ospf area 448
- 8.3.2.5 1583compatibility 449
- 8.3.2.6 area default-cost 449
- 8.3.2.7 area nssa 449
- 8.3.2.13 area range 452
- 8.3.2.14 area stub 452
- 8.3.2.16 area virtual-link 453
- 8.3.2.22 auto-cost 456
- 8.3.2.23 bandwidth 456
- 8.3.2.24 capability opaque 457
- 8.3.2.25 clear ip ospf 457
- 8.3.2.32 default-metric 459
- 8.3.2.33 distance ospf 460
- 8.3.2.38 ip ospf cost 462
- 8.3.2.41 ip ospf network 463
- 8.3.2.42 ip ospf priority 464
- 8.3.2.45 ip ospf mtu-ignore 465
- 8.3.2.46 router-id 465
- 8.3.2.47 redistribute 466
- 8.3.2.48 maximum-paths 466
- 8.3.2.50 passive-interface 467
- 8.3.2.51 timers spf 467
- 8.4.1 Show Commands 468
- 8.5.1 Show Commands 471
- 8.5.1.1 show ip rip 471
- 8.5.2.1 enable rip 473
- 8.5.2.2 ip rip 474
- 8.5.2.3 auto-summary 474
- 8.5.2.5 default-metric 475
- 8.5.2.6 distance rip 475
- 8.5.2.7 hostrouteaccept 476
- 8.5.2.8 split-horizon 476
- 8.5.2.9 distribute-list 477
- 8.5.2.10 redistribute 477
- 8.6.1 Show Commands 479
- 8.6.1.1 show ip irdp 479
- 8.6.2.1 ip irdp 480
- 8.6.2.2 ip irdp broadcast 481
- 8.6.2.3 ip irdp holdtime 481
- 8.6.2.6 ip irdp preference 482
- 8.7 VLAN Routing Commands 483
- 8.7.2 vlan routing 484
- 8.8.1 Show Commands 484
- 8.8.1.1 show ip vrrp 484
- 8.8.1.2 show ip vrrp brief 485
- 8.8.2.1 ip vrrp 487
- 8.8.2.2 ip vrrp ip 488
- 8.8.2.3 ip vrrp mode 488
- 8.8.2.5 ip vrrp preempt 489
- 8.8.2.6 ip vrrp priority 490
- 9. IP Multicast Commands 493
- 9.1.1.5 show ip dvmrp prune 496
- 9.1.1.6 show ip dvmrp route 496
- 9.1.2.1 ip dvmrp 497
- 9.1.2.2 ip dvmrp metric 498
- 9.2.1 Show Commands 498
- 9.2.1.1 show ip igmp 498
- 9.2.2.1 ip igmp 503
- 9.2.2.2 ip igmp version 503
- 9.2.2.7 ip igmp robustness 506
- 9.3 MLD Commands 507
- 9.3.2.5 ipv6 mld router 512
- 9.4 Multicast Commands 513
- 9.4.2.1 ip multicast 518
- 9.4.2.2 ip mcast boundary 518
- 9.5.1 Show Commands 519
- 9.5.1.1 show ip pimdm 519
- 9.5.2.1 ip pimdm 522
- 9.5.2.2 ip pimdm 522
- 9.6.1 Show Commands 523
- 9.6.1.1 show ip pimsm 523
- 9.6.1.2 show ip pimsm bsr 524
- 9.6.2.1 ip pimsm 527
- 9.6.2.5 ip pimsm rp-address 528
- 9.6.2.6 ip pimsm 529
- 9.6.2.8 ip pimsm bsr-border 530
- 9.7 IGMP Proxy Commands 532
- 9.7.2.1 ip igmp-proxy 535
- 9.8 MLD Proxy Commands 537
- 9.8.2.1 ipv6 mld-proxy 540
- 10. IPv6 Commands 542
- 10.1.2.1 interface tunnel 543
- 10.1.2.2 tunnel source 543
- 10.1.2.3 tunnel destination 544
- 10.1.2.4 tunnel mode ipv6ip 544
- 10.2.1 Show Commands 545
- 10.2.2.1 interface loopback 545
- 10.3 IPv6 Routing Commands 546
- 10.3.1.5 show ipv6 ndp 549
- 10.3.1.6 show ipv6 route 550
- 10.3.1.9 show ipv6 vlan 552
- 10.3.1.10 show ipv6 traffic 553
- 10.3.2.1 ipv6 forwarding 556
- 10.3.2.2 ipv6 hop-limit 556
- 10.3.2.4 ipv6 enable 557
- 10.3.2.5 ipv6 address 557
- 10.3.2.6 ipv6 gateway 558
- 10.3.2.7 ipv6 route 559
- 10.3.2.9 ipv6 mtu 560
- 10.3.2.18 ipv6 nd prefix 564
- 10.3.2.19 ipv6 unreachables 565
- 10.4 OSPFv3 Commands 566
- 10.4.1.2 show ip ospf abr 568
- 10.4.2.1 ipv6 ospf 579
- 10.4.2.2 ipv6 ospf areaid 579
- 10.4.2.3 ipv6 ospf cost 580
- 10.4.2.7 ipv6 ospf network 581
- 10.4.2.8 ipv6 ospf priority 582
- 10.4.2.11 ipv6 router ospf 583
- 10.4.2.13 area nssa 584
- 10.4.2.19 area range 587
- 10.4.2.20 area stub 588
- 10.4.2.27 auto-cost 591
- 10.4.2.30 distance ospf 593
- 10.4.2.31 enable 593
- 10.4.2.34 maximum-paths 595
- 10.4.2.36 passive-interface 595
- 10.4.2.37 redistribute 596
- 10.4.2.38 router-id 596
- 10.5 RIPng Commands 597
- 10.5.2.1 enable 598
- 10.5.2.2 ipv6 rip 598
- 10.5.2.3 ipv6 router rip 599
- 10.5.2.5 default-metric 599
- 10.5.2.6 distance rip 600
- 10.5.2.7 split-horizon 600
- 10.5.2.8 redistribute 601
- 10.5.2.9 ipv6 rip timer 601
- 10.6.1 Show Commands 602
- 10.6.1.1 show ipv6 pimdm 602
- 10.6.2.1 ipv6 pimdm 604
- 10.7.1 Show Commands 605
- 10.7.1.1 show ipv6 pimsm 605
- 10.7.2.1 ipv6 pimsm 608
- 10.7.2.7 ipv6 pimsm ssm 611
- 11.1 Overview 614
- 11.2 System Menu 615
- 11.2.3.6 HTTP Configuration 624
- 11.2.5 Viewing Logs 637
- 11.2.7 Defining sFlow 653
- 11.2.8 Defining SNMP 658
- 11.2.9 Viewing Statistics 662
- 11.2.13 Configuring SNTP 683
- 11.3 Switching Menu 695
- 11.3.4 Managing Filters 707
- 11.3.11 Managing Voice VLAN 722
- 11.3.12 Defining GARP 723
- - Sets the maximum 761
- 11.3.22 Managing LLDP 764
- 11.3.23 Managing LLDP-MED 772
- 11.3.24 Managing VTP 778
- 11.3.25 Managing Link State 780
- 11.4 Routing Menu 784
- 11.4.2.1 Configuring IP 787
- 11.4.3 Managing OSPF 792
- 11.4.3.1 Configuring OSPF 792
- 11.4.3.2 Configuring Area 794
- 11.4.9 Managing VRRP 827
- 11.4.9.1 Configuring VRRP 827
- 11.4.10 Managing Tunnels 835
- 11.5 Security Menu 839
- 11.5.2 Managing RADIUS 850
- 11.6 IPv6 Menu 861
- - 865 865
- 11.6.8 Managing IPv6 Routes 887
- 11.6.9 Managing RIPv6 890
- 11.7 QOS Menu 893
- 11.8 IPv4 Multicast Menu 926
- 11.9 IPv6 Multicast Menu 951
- 11.9.2 Managing PIM-DM 959
Relacionado con productos y manuales para Accesorios De Computador Fortinet 548B
Accesorios De Computador Fortinet 5003 Manual de usuario
(128 paginas)
(128 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales